JMR electronic PUB-00281 Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Kontrolery RAID JMR electronic PUB-00281. JMR electronic PUB-00281 User's Manual [en] [es] [fr] Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj

Podsumowanie treści

Strona 1 - FFoorrccee

FFoorrccee44G15 & G15+ RAID Systems15-bay Rackmount and Tower EnclosuresInstallation GuideMay 31, 2002 • Revision APatent Pending

Strona 2

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev ADisclaimerThe original product packaging has been tested and is safe under normal shi

Strona 3 - Contents

SYS-FLTThe SYS-FLT LED on the back of the unit indicates an error on the SES bus. Italso indicates whether an active loop connection is established.

Strona 4

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev A3-1This chapter covers Fibre Channel device installation for both the FORTRAFFoorrcc

Strona 5 - 1. Introduction

Follow the steps in reverse to reinstall.Drive InstallationDevice mounting screws are included with the unit for device mounting. TheJMR part number

Strona 6 - Rackmount Specifications

4. Repeat steps 1 through 3 until all devices are installed, then move ontostep 5 to complete unit setup and installation.5. Configure ID and other op

Strona 7 - Fibre Channel Features

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev A4-1This chapter covers Fibre Channel device configuration and option settings. TheFO

Strona 8 - ID Selection

Setting ID Rotary switch settings only affect Slot 0 and all other slots are sequentiallyincreased by a value of one after that slot.The ID is setsequ

Strona 9 - 2. Hardware Specification

1G Option SettingBy setting the rotary switch settings to “7” - “F”, the enclosure will operate in 1Gmode. Both the upper set of switches and lower s

Strona 10 - Fault Indication Features

Delayed Start Option JumperHeader W1 pins 1 & 2. Jumper on = enabled. Jumper off = disabled (default).Remote Start Option JumperHeader W1 pins 3

Strona 11

External I/O ConnectionThe external I/O connections are located on the personality card There are fourSFP tranceiver connectors accessible from the r

Strona 12 - 3. Device Installation

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev AIICopyrightCopyright 2000, 2001 by JMR Electronics, Inc. All Rights Reserved. No p

Strona 13 - Drive Installation

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev AMuteThis is a push button used to silence the Audible Alarm.SYS Activity LEDThis is a

Strona 14

This chapter covers all operations of the blowers for FORTRAFFoorrccee44G15 andG15+ units. Refer to Chapter 1 for blower specifications. The blowe

Strona 15 - 4. Fibre Channel JBOD Setup

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev A5-2User’s removing or installing a blower must be awarre of theblower access hole. Co

Strona 16 - Setting ID

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev A6-1This chapter covers all operations of the power supplies. For operation, the ACco

Strona 17 - ID Conflict

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev ALow Power Mode (Standby Power)When both power supplies are turned off, the unit will

Strona 18 - Front Status LEDs

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev A7-1This chapter covers the installation of the Rackmount enclosure into a standard19&

Strona 19 - External I/O Connection

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev A7-2Rail Mounting Kit Hardware• Ten #10-32 Screws• Four each #8-32 Screws/Washers/Nuts

Strona 20 - SYS Activity LED

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev A2. Affix the extension bracket tothe rear of the unit using two#10-32 screws. There

Strona 21 - 5. Blower Operation

4. Slide the unit into the cabinet and secure it to the cabinet with a single#10-32 screw on each side.5. Snap the end cap over the screw on each side

Strona 22 - Blower Replacement

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev A8-1For bus management, the FORTRAFFoorrccee44G15 and G15+ 2G Fibre channelenclosure

Strona 23 - 6. Power Supply Operation

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev ATable of Contents1. IntroductionFORTRAProduct Family Features . . . . . . . . . .

Strona 24 - Power Supply Replacement

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev A9-1This chapter covers the installation of the Intel PCI RAID Controller that isshipp

Strona 25 - 7. FR15 Cabinet Installation

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev A10-1For current information on this product, including updates to the manual andtechn

Strona 26 - Rail Installation

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev AA-1Drive ManufacturersFujitsuInternet Address: www.fcpa.comHitachiInternet Address: w

Strona 27 - Two #10-32

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev AHost Bus Adapter ManufacturersAdaptec, Inc.Internet Address: www.adaptec.comAntares M

Strona 28 - #10-32 screw on each side

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev AOption Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Strona 29 - 8. SES Operation

The FORTRAFFoorrccee44G15 & G15+ RAID Systems are prepackaged 2G Fibreto 2G Fibre RAID solutions designed to be used with the included Intel PC

Strona 30 - PCI RAID Controller

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev AFORTRAFFoorrccee44products use advanced mid-plane technology developed byJMR, which

Strona 31 - 10. Product Support

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev ATower SpecificationsDimensions/WeightUnit Weight 43 lbs. (19.5kg)Height 20-1/2"

Strona 32 - C ONTROLLER

ID Selection0-127 device ID addresses are addressable and can be easily set-up via ID rotaryswitches located on the personality modules. For specific

Strona 33

FORTRAFORCE4G15 & G15+ RAID System Installation Guide Rev A2-1This chapter covers specification information for all FORTRAFFoorrccee44G15Tower

Komentarze do niniejszej Instrukcji

Brak uwag